| |
Description | Fiber Optic Ethernet Media Converter kit.Requires a small form-factor pluggable (SFP) module (sold separately). |
Data Interface | Ethernet |
Data Rate | 10/100 MbpsIEEE 802.3 CompliantFull Duplex or Half Duplex Electrical PortFull Duplex Optical Port |
Compatible Receiver | CNFE2MC/IN |
Installation | Installed inside a NDA-U-PAx, VG4-A-PAx or a VG4-A-PSUx power supply box, or in a MIC IP PSU, with supplied mounting hardware. Note: Wiring for the VG4-SFPSCKT must be routed through the proper conduit opening on the power supply box. Refer to the installation guide that accompanies the module. |
LED Indicators | |
Power/Link (on circuit board) | |
Green | Power is applied, fiber link is valid. |
Red | Power is applied, fiber link is missing. |
Green/Flashing Red, rapid | Power is applied.Fiber link is valid.Data is present and video is streaming from the camera to a network connection. |
Green/Flashing Red, slow | Power is applied.Fiber link is valid.Data is present.Video is not streaming from the camera, or the RJ45 connection to the camera is not valid. |
RJ-45 Connector | |
Right side, Flashing Green | Data is present. |
Right side, Off | No data is present. |
Left side, Amber | Link is valid at 100 MB. |
Left side, Off | If the right side is flashing green, link is valid at 10 MB. |
No LED lit | The network cable is missing, is defective, or the other end of the network cable is not connected. |
Electrical | |
Power | 24 VAC @ 220 mA (supplied by the camera) |
Current Protection | Automatic resettableSolid-state current limiters |
Circuit Board | Meets IPC Standard. |
Mechanical | |
Dimensions (LxWxH) | 7.4 x 7.1 x 3.8 cm (2.9 x 2.8 x 1.5 in.) |
Shipping Weight | 0.91 kg (2 lb) |
Environmental | |
MTBF | > 100,000 hours |
Operating Temperature | -40 °C to +50 °C(-40 °F to +122 °F) |
| |
Description | Fiber Optic Ethernet Media Converter kit. Requires a small form-factor pluggable (SFP) module (sold separately). |
Data Interface | Ethernet |
Data Rate | 10/100 MbpsIEEE 802.3 CompliantFull Duplex or Half Duplex Electrical PortFull Duplex Optical Port |
Installation | Surface mount or rack mount using C1-IN rack (sold separately) |
Connectors | |
Power | Terminal block |
Electrical | RJ-45 (10/100 BASE-T/TX) |
Socket | SFP (10/100 BASE-FX) |
LED Indicators | |
Link/Act | |
Green | Indicates a good fiber connection. |
Flashing Green | Indicates data is present on at least one side of the IP connection. |
No LED lit | Indicates a loss of fiber connection. |
Power | Green: power is supplied.None: no power supplied. |
Green | Power is supplied. |
No LED lit | No power supplied. |
RJ-45 Connector | |
Right side, Flashing Green | Data is present. |
Right side, Off | No data is present. |
Left side, Amber | Link is valid at 100 MB. |
Left side, Off | If the right side is flashing green, link is valid at 10 MB. |
Electrical | |
Power | |
Supplied Power Pack | Input: 90-264 VAC, 50/60 HzOutput: 9 VDC @ 1 A |
Module: | 8-15 VDC @ 220 mA |
Current Protection | Automatic resettableSolid-state current limiters |
Circuit Board | Meets IPC Standard. |
Mechanical | |
Dimensions (LxWxH) | 16.0 x 13.0 x 2.8 cm (6.3 x 5.1 x 1.1 in.) |
Shipping Weight | 0.91 kg (2 lb) |
Environmental | |
MTBF | > 100,000 hours |
Operating Temperature | -40 °C to +75 °C (-40 °F to +167 °F) |
Storage Temperature | -40 °C to +85 °C (-40 °F to +185 °F) |
Relative Humidity | 0% to 95% (non-condensing) |
Regulatory Compliance | cUL, UL, RoHS |
| |
Description | Interchangeable modules available for use with MMF or SMF optical fiber. |
Data Interface | Ethernet |
Data Rate | 10/100 MbpsIEEE 802.3 Compliant |
Mechanical | |
Dimensions (LxWxH) | |
SFP-2, SFP-3 | 55.5 x 13.5 x 8.5 mm (2.2 x 0.5 x 0.3 in.) |
SFP-25, SFP-26 | 63.8 x 13.5 x 8.5 mm (2.5 x 0.5 x 0.3 in.) |
Weight (all SFP modules) | 0.23 kg (0.05 lb) |
Type | Connector , Wavelength (transmit/receive) , Max. Distance |
SFP-2 | MMF , Duplex LC , 1310 nm / 1310 nm , 2 km(1.2 miles) |
SFP-3 | SMF , Duplex LC , 1310 nm / 1310 nm , 20 km(12.4 miles) |
SFP-25 | MMF , Single SC , 1310 nm / 1550 nm , 2 km(1.2 miles) |
SFP-26 | MMF , Single SC , 1550 nm / 1310 nm , 2 km(1.2 miles) |
Fiber Compatibility | |
Optical Fiber Compatibility, MMF | 62.5/125 µm MMF. For 50/125 µm fiber, subtract 4 dB from the specified optical budget value. Must meet or exceed fiber standard ITU-T G.651. |
Optical Fiber Compatibility, SMF | 8–10/125 µm SMF. Must meet or exceed fiber standard ITU-T G.652. |
Optical Distance Specifications | Specified transmission distances are limited to the optical loss of the fiber and any additional loss introduced by connectors, splices, and patch panels. The modules are designed to operate over the entire optical loss budget range, so they do not require a minimum loss in order to operate. |
Environmental | |
MTBF | > 100,000 hours |
Operating Temperature | -40 °C to +50 °C(-40 °F to +122 °F) |
| |
Description | Rack mount card cage designed to hold a maximum of 14 CNFE2MC/IN modules |
LED Indicators | |
Power | |
Red | Power is supplied. |
No LED lit | No power. |
Electrical | |
Input Voltage | 90-264 VAC at 1 A maximum |
Output Voltage | 9 VDC ± 5% at 6.5 A at +75 °C (+167 °F) |
Fusing | 1.25 A slow blow (rack power supply)(plug-in modules individually electronically fused) |
Power Indicator | Red LED |
AC Line Cord | Detachable, IEC-connected. US, European, and UK power cords supplied. |
Mechanical | |
Dimensions (LxWxH) | 48 x 19 x 15 cm (19.0 x 7.5 x 6.0 in.) |
Rack Slots | Fourteen (14) 1-in. slots available |
Shipping Weight | 3.4 kg (7.5 lb) |
Environmental | |
MTBF | > 100,000 hours |
Operating Temperature | -40 °C to +75 °C (-40 °F to +167 °F), ambient |
Storage Temperature | -40 °C to +85 °C, (-40 °F to +185 °F), ambient |
Heat Generation | 240 BTU |
Regulatory Compliance | FCC part 15, , cUL, UL, RoHS |